Ubuntu16.04搭建FTP服务器
安装ftp
安装ftp:
sudo apt-get update sudo apt-get install vsftpd
检查ftp是否安装:
vsftpd --version
更改配置文件
注意使用sudo命令获得root权限
打开配置文件:
sudo vim /etc/vsftpd.conf
做如下更改:
# Example config file /etc/vsftpd.conf # # The default compiled in settings are fairly paranoid. This sample file # loosens things up a bit, to make the ftp daemon more usable. # Please see vsftpd.conf.5 for all compiled in defaults. # # READ THIS: This example file is NOT an exhaustive list of vsftpd options. # Please read the vsftpd.conf.5 manual page to get a full idea of vsftpd's # capabilities. # # # Run standalone"any" address (::) will accept connections from both IPv6 # and IPv4 clients. It is not necessary to listen on *both* IPv4 and IPv6 # sockets. If you want that (perhaps because you want to listen on specific # addresses) then you must run two copies of vsftpd with two configuration # files. listen_ipv6=YES # # Allow anonymous FTP"root" for uploaded files is not # recommended! #chown_uploads=YES #chown_username=whoever # # You may override where the log file goes if you like. The default is shown # below. xferlog_file=/var/log/vsftpd.log # # If you want, you can have your log file in standard ftpd xferlog format. # Note that the default log file location is /var/log/xferlog in this case. xferlog_std_format=YES # # You may change the default value for timing out an idle session. #idle_session_timeout=600 # # You may change the default value for timing out a data connection. #data_connection_timeout=120 # # It is recommended that you define on your system a unique user which the # ftp server can use as a totally isolated and unprivileged user. #nopriv_user=ftpsecure # # Enable this and the server will recognise asynchronous ABOR requests. Not # recommended for security (the code is non-trivial). Not enabling it, # however, may confuse older FTP clients. #async_abor_enable=YES # # By default the server will pretend to allow ASCII mode but in fact ignore # the request. Turn on the below options to have the server actually do ASCII # mangling on files when in ASCII mode. # Beware that on some FTP servers, ASCII support allows a denial of service # attack (DoS) via the command "SIZE /big/file" in ASCII mode. vsftpd # predicted this attack and has always been safe, reporting the size of the # raw file. # ASCII mangling is a horrible feature of the protocol. #ascii_upload_enable=YES #ascii_download_enable=YES # # You may fully customise the login banner string: ftpd_banner=Welcome to blah FTP service. # # You may specify a file of disallowed anonymous e-mail addresses. Apparently # useful for combatting certain DoS attacks. #deny_email_enable=YES # (default follows) #banned_email_file=/etc/vsftpd.banned_emails # # You may restrict local users to their home directories. See the FAQ for # the possible risks in this before using chroot_local_user or # chroot_list_enable below. #chroot_local_user=YES # # You may specify an explicit list of local users to chroot() to their home # directory. If chroot_local_user is YES, then this list becomes a list of # users to NOT chroot(). # (Warning! chroot'ing can be very dangerous. If using chroot, make sure that # the user does not have write access to the top level directory within the # chroot) chroot_local_user=YES chroot_list_enable=YES # (default follows) chroot_list_file=/etc/vsftpd.chroot_list # # You may activate the "-R" option to the builtin ls. This is disabled by # default to avoid remote users being able to cause excessive I/O on large # sites. However, some broken FTP clients such as "ncftp" and "mirror" assume # the presence of the "-R" option, so there is a strong case for enabling it. #ls_recurse_enable=YES # # Customization # # Some of vsftpd's settings don't fit the filesystem layout by # default. # # This option should be the name of a directory which is empty. Also, the # directory should not be writable by the ftp user. This directory is used # as a secure chroot() jail at times vsftpd does not require filesystem # access. secure_chroot_dir=/var/run/vsftpd/empty # # This string is the name of the PAM service vsftpd will use. pam_service_name=ftp # # This option specifies the location of the RSA certificate to use for SSL # encrypted connections. rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key ssl_enable=NO # # Uncomment this to indicate that vsftpd use a utf8 filesystem. utf8_filesystem=YES
退出编辑模式后,使用:wq保存退出vim.
创建ftp用户
此处的操作需要使用root权限,若操作被拒绝,使用sudo:
sudo mkdir /home/ftpdir sudo useradd ftpdir -d /home/ftpdir -m sudo passwd ftpdir sudo mkdir /home/ftpdir/ftp sudo chmod 777 -R /home/ftpdir/ftp usermod -s /sbin/nologin ftpdir
配置完成后,添加用户:
sudo vim /etc/vsftpd.chroot_list
将ftpdir添加在文件中。
ftpdir
到此为止,整个ftp的搭建过程就完成了,接下来就是关于如何去使用了。
启动或者重启ftp
启动或者重启ftp:
service vsftpd startservice vsftpd restart
查看ftp状态:
service vsftpd status
若要关闭ftp服务,可以使用如下命令:
service vsftpd stop
查看服务器ip
打开命令端
robot@robot:~$ ifconfig enp4s0f2 Link encap:Ethernet HWaddr 74:d0:2b:ec:fa:f9 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:12840 errors:0 dropped:0 overruns:0 frame:0 TX packets:12840 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1174976 (1.1 MB) TX bytes:1174976 (1.1 MB) wlp3s0 Link encap:Ethernet HWaddr 24:fd:52:85:42:0c inet addr:192.168.1.110 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::c13c:b38e:69c7:cdf2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:99764 errors:0 dropped:0 overruns:0 frame:0 TX packets:95225 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:98718687 (98.7 MB) TX bytes:14326894 (14.3 MB)
由于此处连接的是wifi,因此在wlp3s0这里找到对应的ip地址为192.168.1.110(如果连接网线则在第一段找ip,每台电脑的配置都不一样,可根据实际情况考虑)
登陆
使用filezilla或者打开文件管理器输入ftp://ipaddress
打开计算机,输入服务器的ip地址ftp://192.168.1.110
输入用户名和密码,此处使用的用户名为ftpdir
,密码为123456
最后就可以看到服务器上的创建的文件夹了。
ubuntu上文件位置
在完成ftp服务器的搭建和测试工作后,文件存放在服务哪里呢,怎么找到这些文件?
在创建用户那一节,在/home
目录这里创建了ftpdir
文件夹,ftpdir
文件夹里创建了一个可读可写的文件夹ftp
,在之后的文件传输中,可以切换到ftp
文件夹中寻找文件,此处操作需要使用sudo
获取权限。
robot@robot:~$ cd /home/ftpdir/ftp robot@robot:/home/ftpdir/ftp$ ls 魔方.zip
至此,整个过程就结束了,在搭建的过程中,参考了网上其他前辈的经验,这仅作为学习之路上的笔记,所提到的东西若有错误,欢迎各位指出!
总结
以上所述是小编给大家介绍的Ubuntu16.04环境下搭建FTP服务器的教程,希望对大家有所帮助,如果大家有任何疑问请给我留言,小编会及时回复大家的。在此也非常感谢大家对网站的支持!
如果你觉得本文对你有帮助,欢迎转载,烦请注明出处,谢谢!
免责声明:本站资源来自互联网收集,仅供用于学习和交流,请遵循相关法律法规,本站一切资源不代表本站立场,如有侵权、后门、不妥请联系本站删除!
更新日志
- 小骆驼-《草原狼2(蓝光CD)》[原抓WAV+CUE]
- 群星《欢迎来到我身边 电影原声专辑》[320K/MP3][105.02MB]
- 群星《欢迎来到我身边 电影原声专辑》[FLAC/分轨][480.9MB]
- 雷婷《梦里蓝天HQⅡ》 2023头版限量编号低速原抓[WAV+CUE][463M]
- 群星《2024好听新歌42》AI调整音效【WAV分轨】
- 王思雨-《思念陪着鸿雁飞》WAV
- 王思雨《喜马拉雅HQ》头版限量编号[WAV+CUE]
- 李健《无时无刻》[WAV+CUE][590M]
- 陈奕迅《酝酿》[WAV分轨][502M]
- 卓依婷《化蝶》2CD[WAV+CUE][1.1G]
- 群星《吉他王(黑胶CD)》[WAV+CUE]
- 齐秦《穿乐(穿越)》[WAV+CUE]
- 发烧珍品《数位CD音响测试-动向效果(九)》【WAV+CUE】
- 邝美云《邝美云精装歌集》[DSF][1.6G]
- 吕方《爱一回伤一回》[WAV+CUE][454M]